RIFF Box – JTAG Revolution

30.12.2011    HTC Incredible S Unbrick, Unlock, CID, IMEI repair supported

Resurrecting HTC Incredible S is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Incredible S boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 1.13.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG3213000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Incredible S:

•  Solder JTAG cable to HTC Incredible S JTAG pads;
•  Insert batter and connect USB Data cable;
•  Make sure HTC Incredible S is selected in the list of models;
•  If you use only battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

_

Share!

Tweet

Follow

26.10.2011  Samsung Galaxy S Plus (i9001) Unbrick, boot repair supported

Resurrecting Samsung I9001 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Please note, MSM8255T is dual core chipset – it has ARM11 and Qualcomm Scorpion cores. During power on sequence only ARM11 core is visible on the JTAG chain. If boots are not completely damaged and it comes up to initializing of the Scorpion core then Scorpion core appears on the JTAG chain too. This will shift ARM11 from TAP0 into TAP1 position on the chain, while current resurrector has the ARM11 core hardcoded at TAP0 position. Thus make sure to establish JTAG connection in the time range while Scorpion core is not visible yet.

To resurrect Samsung I9001:

•  Solder JTAG cable to Samsung I9001 JTAG pads;
•  Make sure Samsung I9001 is selected in the list of models;
•  Insert battery and connect USB Data cable;
•  If you use only battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

Share!

Tweet

Follow

24.10.2011  HTC Desire CDMA Supported

Resurrecting HTC Desire CDMA is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.60.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PP9940000’.
Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC Desire CDMA:

•  Solder JTAG cable to HTC Desire CDMA JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure HTC Desire CDMA is selected in the list of models;
•  If you use battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Back’ key and press ‘Power ON’ button.

Share!

Tweet

Follow

24.10.2011   HTC Supersonic (EVO 4G) Unbrick, Unlock, IMEI, CID, ModelID repair supported

Resurrecting HTC Supersonic (EVO 4G) is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.16.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC3610000’.
Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code. If selected, then ClockworkMod Recovery v5.0.2.2 will be flashed. Using this recovery you will be able to install zip files from the SD Card, for example you will be able to acquire ROOT rights by installing su-2.3.6.3-efgh-signed.zip file.

To resurrect HTC Supersonic:

•  Solder JTAG cable to HTC Supersonic JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure HTC Supersonic is selected in the list of models;
•  If you use battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

Share!

Tweet

Follow

12.10.2011    HTC Desire Z (HTC Vision) Unbrick, Unlock, IMEI&CID repair supported

Resurrecting HTC Desire Z is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Desire Z boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.

Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write one of selected PDA’s SPL versions (0.76.2000 or 0.85.0005). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC1010000’.
There is option to reflash BOOT and RECOVERY zones.

Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Desire Z:

•  Solder JTAG cable to HTC Desire Z JTAG pads;
•  Insert batter and connect USB Data cable;
•  Make sure HTC Desire Z is selected in the list of models;
•  If you use only battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

Share!

Tweet

Follow

09.09.2011  HTC Desire S S510E (HTC Saga) – Unbrick, Unlock, CID, IMEI Update supported
Resurrecting HTC Desire S is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Desire S boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL to 0.98.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG8810000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC Desire S:

•  Solder JTAG cable to HTC Desire S JTAG pads;
•  Insert batter and connect USB Data cable;
•  Make sure HTC Desire S is selected in the list of models;
•  If you use only battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

Share!

Tweet

Follow

02.08.2011   Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported

Resurrecting SE X8 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.
To resurrect SE X8:

•  Solder JTAG cable to SE X8 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure SE X8 is selected in the list of models;
•  If you use only battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

Share!

Tweet

Follow

02.08.2011    Sony Ericsson Xperia X10a mini / E10a (SE Robyn) Unbrick – Boot repair supported

Resurrecting SE X10 Mini is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.
To resurrect SE X10 Mini:

•  Solder JTAG cable to SE X10 Mini JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure SE X10 Mini is selected in the list of models;
•  If you use only battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

Share!

Tweet

Follow

30.07.2011     SonyEricsson Xperia X10 Unbrick – Boot repair supported

Resurrecting SE X10 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Be careful, JTAG pads are covered under blue mask covering, so you will need to scratch it off in order to be able to solder wires.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.

To resurrect SE X10:

•  Solder JTAG cable to SE X10 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure SE X10 is selected in the list of models;
•  If you use only battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

Share!

Tweet

Follow

07.07.2011  HTC Wildfire S A510E (HTC Marvel), More CDMA models supported.

Resurrecting HTC WildFireS is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4910000′. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC WildFireS:

•  Solder JTAG cable to HTC WildFireS JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure HTC WildFireS is selected in the list of models;
•  If you use battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.

 

• Samsung B139 Repair/Unbrick, Read/Write NOR Flash
• Samsung B259 Repair/Unbrick, Read/Write NOR Flash
• Samsung B309 Repair/Unbrick, Read/Write NOR Flash
• Samsung B319 Repair/Unbrick, Read/Write NOR Flash
• Samsung B379 Repair/Unbrick, Read/Write NOR Flash
• Samsung B619 Repair/Unbrick, Read/Write NOR Flash
• Huawei C31 Repair, Read/Write NOR flash

Share!

Tweet

Follow