RIFF Box – Best JTAG Box in this Galaxy :) Easy to operate !

Tag: Spl

RIFF JTAG – HTC EVO Design 4G / Acquire (HTC Kingdom) Unbrick, IMEI, SuperCID, Unlock repair supported

by on Mar.09, 2013, under News

09.03.2013 RIFF JTAG – HTC EVO Design 4G / Acquire (HTC Kingdom) Unbrick, IMEI, SuperCID, Unlock repair supported

Repairing bricked HTC EvoDesign4G is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zones and will re-write PDA’s SPL to 1.30.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH4410000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC EvoDesign4G via USB Cable:

  •  If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
  •  Make sure USB cable is attached to the board and is connected to PC;
  •  Make sure HTC EvoDesign4G via USB is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_evo_design_4g

Comments Off :, , , , , , , , , , , , , , , , , , , , , more...

RIFF JTAG – HTC Desire C NFC A320e (HTC Golf) Unbrick, Unlock, SuperCID, IMEI repair supported

by on Feb.20, 2013, under News

20.02.2013 RIFF JTAG – HTC Desire C NFC A320e (HTC Golf) Unbrick, Unlock, SuperCID, IMEI repair supported

Repairing bricked HTC Desire C (PL0110000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.25.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PL0110000’.

To resurrect HTC Desire C (PL0110000):

  •  Solder JTAG cable to HTC Desire C (PL0110000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire C (PL0110000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_c

Comments Off :, , , , , , , , , , , , , , , , , , , more...

RIFF JTAG – HTC Desire X (HTC Proto) Unbrick , Unlock, SuperCID and IMEI repair supported

by on Feb.14, 2013, under News

14.02.2013    RIFF JTAG – HTC Desire X (HTC Proto) Unbrick , Unlock, SuperCID and IMEI repair supported

Repairing bricked HTC Desire X (PM6610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.24.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PM6610000’.

To resurrect HTC Desire X (PM6610000):

  •  Solder JTAG cable to HTC Desire X (PM6610000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire X (PM6610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_x_2

Comments Off :, , , , , , , , , , , , , , , , , , , , more...

RIFF JTAG – HTC One XL (HTC Evita) Unbrick – Dead boot, Unlock, SuperCID, IMEI repair supported

by on Feb.09, 2013, under News

09.02.2013   RIFF JTAG – HTC One XL (HTC Evita) Unbrick – Dead boot, Unlock, SuperCID, IMEI repair supported

Repairing bricked HTC OneXL (PJ8312000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ8312000’.

To resurrect HTC OneXL (PJ8312000):

  •  Solder JTAG cable to HTC OneXL (PJ8312000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneXL (PJ8312000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_xl

Comments Off :, , , , , , , , , , , , , , , , , , , more...

RIFF JTAG – HTC Droid DNA ADR6435 / Droid Incredible X (HTC DLX) Unbrick, Unlock, IMEI and SuperCID repair supported

by on Jan.31, 2013, under News

RIFF JTAG – HTC Droid DNA ADR6435 / Droid Incredible X (HTC DLX) Unbrick, Unlock, IMEI and SuperCID repair supported

Repairing bricked HTC Droid DNA (PL8320000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.33.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PL8320000’.

To resurrect HTC Droid DNA (PL8320000):

  •  Solder JTAG cable to HTC Droid DNA (PL8320000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Droid DNA (PL8320000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_droid_dna

Comments Off :, , , , , , , , , , , , , , , , , , , more...

RIFF JTAG – HTC One X AT&T Unbrick, IMEI, SuperCID repair supported

by on Jan.30, 2013, under News

30.01.2013 RIFF JTAG – HTC One X AT&T(PJ8310000) Unbrick, IMEI, SuperCID repair supported

Repairing bricked HTC OneX (PJ8310000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ8310000’.

To resurrect HTC OneX (PJ8310000):

  •  Solder JTAG cable to HTC OneX (PJ8310000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneX (PJ8310000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_x

Comments Off :, , , , , , , , , , , , , , , , , , , more...

RIFF JTAG – HTC Desire V T328w (HTC Wind) Unbrick, IMEI, SuperCID, Boot repair supported

by on Jan.15, 2013, under News

15.01.2013 RIFF JTAG – HTC Desire V T328w (HTC Wind) Unbrick, IMEI, SuperCID, Boot repair supported

Repairing bricked HTC DesireV (PL1110000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.14.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PL1110000’.

To resurrect HTC DesireV (PL1110000):

  •  Solder JTAG cable to HTC DesireV (PL1110000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC DesireV (PL1110000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_v_t328w_2

Comments Off :, , , , , , , , , , , , , , , , , , , more...

RIFF JTAG – HTC One S PJ401000 Unbrick, Unlock, IMEI, SuperCID repair supported

by on Dec.29, 2012, under News

29.12.2012  RIFF JTAG – HTC One S PJ401000 Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC OneS (PJ4010000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.06.0000 or 1.13.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ4010000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneS PJ4010000 is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_s

Comments Off :, , , , , , , , , , , , , , , , , , , , more...

RIFF JTAG – AT&T HTC Status (HTC ChaCha PH0613000) Ubrick, Boot, IMEI, SuperCID repair supported

by on Dec.29, 2012, under News

29.12.2012  RIFF JTAG – AT&T HTC Status (HTC ChaCha PH0613000) Ubrick, Boot, IMEI, SuperCID repair supported

Repairing bricked HTC ChaCha (HTC Status) (PH0613000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.13.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH0613000’.

To resurrect HTC ChaCha:

  •  Solder JTAG cable to HTC ChaCha (PH0613000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC ChaCha (PH0613000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_status

Comments Off :, , , , , , , , , , , , , , , , , , , more...

RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

by on Nov.21, 2012, under News

21.11.2012  RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

Repairing bricked HTC OneS is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.09.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ4020000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneS is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

Comments Off :, , , , , , , , , , , , , , , , , , , , more...

Looking for something?

Use the form below to search the site:

Still not finding what you're looking for? Drop a comment on a post or contact us so we can take care of it!

Archives

All entries, chronologically...